Fusee: lfs kernel patches for 3.0.0/3.0.2

Fusee: Complete hashes (Thanks @Thog), lfs patches for 2.0.0

Fusee: Add kernel patches for 1.0.0.

Fix a few issues in the secondary kernel_patches.c file

Merge pull request #145 from Traiver/master ...

fusee: Add 4.1.0 kernel patch definitions

Update kernel_patches.c

Update kernel_patches.c

Update kernel_patches.c

add kernel patches for 4.1.0

fusee: correct 4.x free_code_space_offset value

fusee: Add 3.0.0-3.0.1 kernel hash (and free_code_space_offset)

Rework sdmmc clocking configuration ...

Use 204 MHz as host clock in SDR104 mode instead of 136 MHz.
Due to this, also change the frequency init divider so the
initialization frequency is below 400 kHz.
This makes the clocks for SDMMC1 in all modes to match the TRM table.

Make it clear in the code that HS200/HS400 modes in fact use PLLP_OUT0
and not PLLC4_OUT2_LJ like the comment suggest. In fact selecting the
PLLC4_OUT2_LJ as clock source results in freeze after switching to
HS200/HS400 mode. This is most likely related to the PLLC4 not being
enabled, but it should be checked later.

Set the HS200/HS400 divider to 3, as this is what the code really did
set prior to this change - so this commit does not change that.

Configure Legacy 12 MHz clock to run at 12 MHz using the SW default
configuration (as per TRM) for the SDMMC legacy timer.

Introduce initial version of sdmmc_host_clock_delay() in order to use it
in places where the wait is host clock dependent. The way it is
implemented now does not change the sleep that was used instead.

fusee: Run periodic autocal only on the uSD controller (#137)

Merge pull request #132 from tslater2006/master ...

Add sdmmc_dump_regs function

Fix race conditions and misconfiguration in sdmmc ...

Properly configure pull up and pull down offsets for autocal.
Run autocal prior to every transfer.

Prevent race conditions in sdmmc_wait_for_event() - make sure the fault
handler has highest priority, then the target irq, state conditions and
finally the error mask.

Do not clear all bits (|=) when acknowledging fault conditions,
only acknowledge the fault conditions itself.

Enable interrupts before preparing command registers - if sdmmc is fast
enough it can actually finish transfer before we enabled the interrupts.
Enabling interrupts clears the COMMAND COMPLETE status bit.

Temporarily print all the sdmmc messages in stage2 - for yet unknown
reason respecting the log level results in some failures.

This results in working microsd card in stage2 on my switch with Samsung
EVO+ 256GB microsd card.

Switched to mmc_debug, and use inttypes

use printf instead of printk for secondary

Add sdmmc_dump_regs function

Make sdmmc autocalibration follow TRM procedure ...

Sleep for 1 us, not 1 ms.
Timeout after 10 ms, set driver strength code values according to TRM.

Fix typo (mS) - time is in milliseconds, not milliSiemens.

Fix logic bug in stage2's main function

package2 verification and ini1 merging fixes (#125) ...

* fusee: Incremet offset while reading kip1s

* fusee: Pass package2 section data along with the decrypted metadata

Pass screen status and mmc struct from stage1 to 2

Merge pull request #114 from desowin/sdmmc-errata ...

Set SDMMC controller to SDR104 as a workaround

fusee: Add kernel hash for 4.x

Fusee: Add 5.x kernel patches to allow for IPC PID mitm.

Fusee: Add mechanism for branching back at end of hook.

Fix CCPLEX bringup and halt the BPMP once it's done booting. (#118)

Fusee: Add infrastructure for applying kernel patches (needed for mitm)

Fusee: Separate kernel patching into its own file.

Set SDMMC controller to SDR104 as a workaround ...

According to Tegra X1 Series Processors Silicon Errata there is possible
misalignment of received data which results in a CRC error. The issue is
present only in SDR50 mode.